Cut Off Dies
 For use in your own punch press
For dimple-free cutting of tubing, these dies are designed for use in your punch press. Our design was originally patented in 1941, and is in use throughout the U.S.A. and the world. Our two-blade method produces cuts on round tubing with no deformation and minimal burr. A slug, (not chips), is produced, from .06" to .125 " thick depending on the blades used.
Since no chips are produced, and burr is typically 10% of the tube's wall thickness or less, most parts can be cut and are ready for the next operation such as expanding or mandrel bending without deburring or chip removal, drastically slashing handling and final piece part costs.
Die blocks move with cams to completely encircle the tube and prevent OD bulging during cut off, as well as provide a sharp cutting edge for the blades to cut against. A horizontal blade is cammed tangentially across the top of the tube to remove enough wall material for the vertical shear blade to enter and complete the cut without deforming the tube.
This method is best used with mild steel tubing, but can be used on other materials, such as aluminum, stainless, half-hard copper, etc. Vogel Cut Off Dies are designed for offline recutting of tubing, (not "flying" as used when cutting tubes during manufacture on a tube mill).
Square tubing is cut with the horizontal blade mechanism removed, with the tube in the corner-over-corner orientation, also resulting in a dimple-free cut. Die blocks are interchangeable to accept a wide range of shapes and sizes up to maximum capacity of the die. Die blocks and blades can be changed without removing the cut off die from your press and all cutting members are designed to be sharpenable.
All dies are shipped with a (not shown) drip-feed lubrication system and a 24" long end-stop and micro-switch stop assembly which signals your press to cycle. This allows material to be cut as fast as the stock can be fed. We also offer complete cut off machines & systems.
| P Series Two-Blade Cut Off Dies |
| Model |
Cutt Off Die Price (less inserts & blades) |
Capacity |
Size |
Approx. Weight |
Insert Length* |
Press Requirements |
Max. strokes per minute |
| OD |
Square |
Wall |
L to R |
F to B |
Shut |
Stroke** |
Tons |
| 1P |
$9,525.00 |
1" |
3/4" |
.125" |
18" |
9" |
250 lbs. |
1-1/12" |
7-1/8" |
3" |
20 |
110 |
| 2P |
$10,895.00 |
2" |
1-1/2" |
.145" |
19" |
11" |
335 lbs. |
2-1/2" |
8-1/8" |
5"~6" |
40 |
85 |
| 3P |
$16,500.00 |
3" |
2-1/8" |
.187" |
24" |
12-1/2" |
435 lbs. |
3" |
11-1/8" |
6" |
70 |
60 |
| 4P |
$25,625.00 |
4" |
2-13/16" |
.250" |
28" |
17" |
520 lbs. |
4" |
14-9/16" |
7" |
120 |
50 |
| 6P |
$42,750.00 |
6" |
3-7/16" |
.250" |
36" |
18" |
950 lbs. |
4" |
14-1/2" |
10" |
160 |
30 | Notes:
* Inserts length determines minimum part length. Die blocks may be incut to allow for shorter part length. Pls. consult factory.
** Reduced stroke dies may be available to suit your press. Reducing stroke reduces maximum capacity of die. Consult factory.
Each die above can also cut rectangular, oval and other shapes of tubing, who's largest dimension doesnot exceed the square capacity shown above. Please consult factory to discuss your application details.
LHP SERIES SINGLE BLADE CUTOFF DIES
Vogel single blade cutoff dies is designed for dimple-free cuts on square and rectangular tubing (or dimpled cuts on rounds).
The LHP may be upgraded at a later date with the horizontal blade mechanism to have full capacity for dimple-free cutting on round tubing.
Die blocks and blades can be changed without removing the cut off die from your press and all cutting members are designed to be sharpenable.
The LHC is dedicated for square or rectangular tubing and is not upgradable.
| 5827 & LHP Series Single Blade Cut Off Dies |
| Model |
Price (less Inserts & Blades) |
Capacity |
Size |
Approx. Weight |
Insert Length* |
Press Requirements |
Max. strokes per minute |
Upgradeable for dimple-free cutting of round tubing? |
| Square |
Wall |
L to R |
F to B |
Shut |
Stroke** |
Tons |
| 5827 LHC |
$6,895.00 |
1-1/8" |
.125" |
18" |
9" |
225 lbs. |
1-1/12" |
7-1/8" |
3" |
20 |
110 |
No |
| 2LHP |
$8,995.00 |
1-1/2" |
.145" |
19" |
11" |
300 lbs. |
2-1/2" |
8-1/8" |
5"~6" |
40 |
85 |
Yes |
| 3LHP |
$15,325.00 |
2-1/8" |
.187" |
24" |
12-1/2" |
400 lbs. |
3" |
11-1/8" |
6" |
70 |
60 |
Yes |
| 4LHP |
$18,550.00 |
2-13/16" |
.250" |
28" |
17" |
475 lbs. |
4" |
14-9/16" |
7" |
120 |
50 |
Yes |
| 6LHP |
$32,975.00 |
3-7/16" |
.250" |
36" |
18" |
875 lbs. |
4" |
14-1/2" |
10" |
160 |
30 |
Yes | Notes:
** Inserts length determines minimum part length. Die blocks may be incut to allow for shorter part length. Pls. consult factory.
Each die above can also cut rectangular tubing, who's largest dimension does not exceed the square capacity shown above.
Frequently Asked Questions
|
)
