Additional information
| Weight | N/A |
|---|---|
| OD Max. Capacity | 1.25", 2", 3" |
| Wall Max. Capacity | .125", .187", .250" |
The Mitre-Snug Angular Notching Tool is designed to miter a tube end at one specific angle, between 25° to 89°.
To produce an angled tube end with a Mitre-Snug tool, you need a housing, a two-station assembly, and a press to provide power. The tools are spring-loaded for easy set-up and notch off slugs, so there are no chips requiring removal!
- No time-consuming fixturing and set-up
- No chip removal requiring secondary handling
- Exact angle every time
- Long-lasting, sharpenable tooling
Select your housing below based on the tube OD to be notched. You will then need to select assemblies for each tube size & angle. [And yes, our Mitre-Snug Housings are the same as our Arc-Snug Housings, so you can reuse the housing at a later date to accept an Arc-Snug Assembly for when a tube needs to be notched to fit against another tube at an angle]
400 Housing specs
12″ wide x 9″ front to back. 6″ shut height x 2″ stroke. Min. 30 tons
450 Housing specs
12″ wide x 9″ front to back. 7-1/2″ shut height x 3″ stroke. Min. 35 ~ 40 tons
455 Housing specs
12″ wide x 9″ front to back. 7-1/2″ shut height x 3″ ~ 4″ stroke. Min. 50 ~ 60 tons
500 Housing specs
13″ wide x 12″ front to back. 10-1/2″ shut height x 4″ stroke. Min. 60 ~ 80 tons
The Mitre-Snug Angular Notching Tool is designed to miter a tube end at one specific angle, between 25° to 89°.
To produce an angled tube end with a Mitre-Snug tool, you need a housing, a two-station assembly, and a press to provide power. The tools are spring-loaded for easy set-up and notch off slugs, so there are no chips requiring removal!
- No time-consuming fixturing and set-up
- No chip removal requiring secondary handling
- Exact angle every time
- Long-lasting, sharpenable tooling
Select your housing below based on the tube OD to be notched. You will then need to select assemblies for each tube size & angle. [And yes, our Mitre-Snug Housings are the same as our Arc-Snug Housings, so you can reuse the housing at a later date to accept an Arc-Snug Assembly for when a tube needs to be notched to fit against another tube at an angle]
400 Housing specs
12″ wide x 9″ front to back. 6″ shut height x 2″ stroke. Min. 30 tons
450 Housing specs
12″ wide x 9″ front to back. 7-1/2″ shut height x 3″ stroke. Min. 35 ~ 40 tons
455 Housing specs
12″ wide x 9″ front to back. 7-1/2″ shut height x 3″ ~ 4″ stroke. Min. 50 ~ 60 tons
500 Housing specs
13″ wide x 12″ front to back. 10-1/2″ shut height x 4″ stroke. Min. 60 ~ 80 tons
Available Options:
Description
The Mitre-Snug Angular Notching Tool is designed to miter a tube end at one specific angle, between 25° to 89°.
To produce an angled tube end with a Mitre-Snug tool, you need a housing, a two-station assembly, and a press to provide power. The tools are spring-loaded for easy set-up and notch off slugs, so there are no chips requiring removal!
- No time-consuming fixturing and set-up
- No chip removal requiring secondary handling
- Exact angle every time
- Long-lasting, sharpenable tooling
Select your housing below based on the tube OD to be notched. You will then need to select assemblies for each tube size & angle. [And yes, our Mitre-Snug Housings are the same as our Arc-Snug Housings, so you can reuse the housing at a later date to accept an Arc-Snug Assembly for when a tube needs to be notched to fit against another tube at an angle]
400 Housing specs
12″ wide x 9″ front to back. 6″ shut height x 2″ stroke. Min. 30 tons
450 Housing specs
12″ wide x 9″ front to back. 7-1/2″ shut height x 3″ stroke. Min. 35 ~ 40 tons
455 Housing specs
12″ wide x 9″ front to back. 7-1/2″ shut height x 3″ ~ 4″ stroke. Min. 50 ~ 60 tons
500 Housing specs
13″ wide x 12″ front to back. 10-1/2″ shut height x 4″ stroke. Min. 60 ~ 80 tons
How do I specify the angle I need?
Specify the angle between the notched tube centerline and the angle across the mitered end, see illustration below. If you wanted to notch a square tube end to create a right-angle corner, like a picture frame, specify a 45° angle. The Mitre-Snug can be ordered for one angle of at least 25° up to 90°. You can always contact us to discuss your needs or send a print of your application
I need more than one angle / I’m not sure what angle I will need.
The Mitre-Snug is designed to consistently notch out one angle. You will need to order additional assemblies each time the tube OD or gauge or angle changes. Remember that this tool is designed for high volume consistent notching of the same application over and over.
I need to put in a drainhole, how can I do this?
You have several choices. The Mitre-Snug can put in a drainhole at the same time it is creating the miter. If you want the drainhole at the deep end of the notch, the drainhole will be added in the first station. If you want the drainhole at the shallow point of the notch, the drainhole will be added in the second station.
If you don’t need the drainhole in every part, you can also purchase an Arc-Fit assembly to create a drainhole (only) to be used as an additional operation after the miter is created.
Can I sharpen / replace my tooling?
Yes, you can replace the punches and / or the dies. You can also send in any of these parts to be sharpened. Please visit our page on sharpening for instructions on returning tools to Vogel for sharpening.
Reviews
There are no reviews yet.